Category Archives: Club Activities

Club Activities or Events

IRLP Node 6214 back on air!

Posted on by

The AREG IRLP node 6214 via VK5RSB 70cm is now back on air and available for general use.

The IRLP nodes “new” computer is now a Raspberry Pi 2, with modifications to the IRLP board to allow for operation on 3 volts as is used by the Raspberry Pi.

During both the morning and afternoon drive times, Monday to Friday, the node 6214 will be off line. It is available all the time Saturday and Sundays.

Weekday morning:

  • off at 07:00am
  • on at 09:30am

Weekday afternoon:

  • off at 3:00pm
  • on at 7:00pm

Access for IRLP operation still requires the current issued access code.

(details may be found at  https://www.areg.org.au/activities/irlp-node-6214)

DTMF “0” is the only “free” access to advise the status of the IRLP linking.

I will write up a blog report with photos for the AREG web pages in due course.

Feedback on the IRLP operations is most welcome, might need to make some level adjustments???

Ben VK5BB

AREG IRLP Node 6214 Administrator

REMINDER: Horus 48 Telemetry Test from Mt Lofty TOMORROW

Posted on by

THOR Receiver Tune & Test Day – Sunday 4th March ~10:30AM CDST

To help stations adapt to the new THOR16 signal, this coming Sunday there will be the opportunity for stations in the Adelaide metropolitan area to set up dl-fldigi as per the linked guide below and have a go receiving a higher-power version of the THOR16 signal. This will be broadcast from Mt Lofty Summit by Mark VK5QI. Mark will be on the VK5RSB 70cm repeater (439.900 -5MHz / 91.5Hz CTCSS) as ‘technical support’, to help assist setting up the software. The signal should be easily receivable from the Adelaide Metro area and some surrounds.

Look for the test signal on 434.640MHz

DL-FLDIgi Setup for THOR16

As usual, use dl-fldigi to decode telemetry, but in the case of the THOR16 payload, you will have to manually select the operating mode from the drop-down list as follows:

 

AREG IRLP Node 6214 Off Air

Posted on by

The following news comes from Ben VK5BB, the custodian of the 6214 IRLP node that is connected to the VK5RSB 70cm repeater

Due to a failure of IRLP node 6214’s computer hardware,
it is off line until further notice!

History:

I took on the management of the IRLP node 6214 sometime around 2012. Prior to this it was managed by Adrian VK5ZSN. Under his management it was all OK until the HDD died.

I volunteered to take on the project and rebuilt the computer using an IDE to SATA adapter and a solid state HDD. A bit of jiggling but it worked and to date has been very reliable with minimum of hands on support to keep it on air. 

Current Status:

I am not sure what is going on but it appears that the computer that manages the IRLP node 6214 is having severe problems. It seems that the computer is unstable and keeps shutting itself down and rebooting. The machine running the system is now over 10 years old, which is a contributing factor.

Right now, the ultimate fate of the IRLP node is undecided. The club members have been asked if they wish to see the service continued. That discussion is ongoing. If the service is to continue, it could be some time before it is restored as new hardware will likely need to be obtained.

If you would like to see it rebuilt and placed back on the air, why not consider becoming a member of AREG and showing your support for the project? Details of how to join are available on our membership page .

ADVANCE NOTICE – Horus 48 – Telemetry Test Flight & Test Transmission

Posted on by

On the weekend of the 10-12th of March (exact day TBD), Project Horus will be performing a small (not-so-)high-altitude balloon launch from Mt Barker. The flight will be a short one (~1.5 hrs), with a maximum expected altitude of only 13km. All the payloads have been custom-built to be very lightweight – the total payload mass for this launch is < 300 grams!

The aim of this flight is to evaluate the performance of a new telemetry payload, which uses ‘THOR16‘ modulation. While about half the speed of the current RTTY payload, the THOR modes utilise forward error correction and interleaving. This promises to reduce or remove issues with mobile flutter and multi-path fading that we encounter with RTTY. In short, while we may not be getting telemetry sentences quite as often, we will have a much higher chance of the telemetry that is received being useful to us!

THOR Receiver Tune & Test Day – Sunday 4th March ~10:30AM CDST

To help stations adapt to the new THOR16 signal, this coming Sunday (a week prior to the launch) there will be the opportunity for stations in the Adelaide metropolitan area to set up dl-fldigi as per the linked guide below and have a go receiving a higher-power version of the THOR16 signal. This will be broadcast from Mt Lofty Summit by Mark VK5QI. Mark will be on the VK5RSB 70cm repeater (439.900 -5MHz / 91.5Hz CTCSS) as ‘technical support’, to help assist setting up the software. The signal should be easily receivable from the Adelaide Metro area and some surrounds.

Look for the test signal on 434.640MHz

Horus 48 Launch Campaign – Tentative 10-12th March

For the actual launch the following weekend, the telemetry frequencies for the flight are as follows:

  • RTTY – ‘HORUS’ – 434.650 MHz
  • THOR16 – ‘THORUS’ – 434.640 MHz

Both payloads are running 10mW transmit power, and have essentially identical antennas.

DL-FLDIgi Setup for THOR16

As usual, use dl-fldigi to decode telemetry, but in the case of the THOR16 payload, you will have to manually select the operating mode from the drop-down list as follows:

If you have the capability of running two 70cm receivers, please consider running two instances of dl-fldigi to decode both payloads. This may require either multiple PCs, or multiple sound cards. If you can only run a single receiver, please try and alternate between the different telemetry payloads.

We would very much appreciate reports as to your experiences decoding the different telemetry payloads – please e-mail these through to vk5qi@rfhead.net

Tracking for the launch will be available on the HabHub online tracker. We hope to see you as part of the tracking nets!

 

73 de Mark VK5QI

 

 

Horus 47: SHSSP 2018 Science Flight Report

Posted on by

Following unfavourable weather conditions the previous weekend, the Amateur Radio Experimenters Group planned a second attempt to fly the science payloads for the Southern Hemisphere Space Studies Program 2018 on Sunday February 4th. Again, the weather was not cooperating, which forced a change of the launch site in order to get off the ground. This meant a very early start as the launch teams left Adelaide at 7.00am to trek 150km east of the city into the Murray Mallee.

This flight was carrying a number of science experiments for the SHSSP students. This year the focus was on space navigation, so one particular focus was using the GPS data coupled with an initertial measurment unit to be able to plot the angle and direction of the camera taking the photos. The other experiment was a spectrometer which was measuring the precise wavelengths of light.

SHSSP18 Downward facing camera (courtesy UniSA and SHSSP)

Launch Preparation

Launch preparations began about 9am after the crew had arrived at the launch site. Thanks must go to Chris VK5CP who arranged access with the farmer who’s paddock we borrowed for the morning. Along the way the obligotory bakery stop had been made in the township of Mannum (I can vouch for their blueberry scrolls). Today we had a couple of new faces on the flight team, with Marcus VK5WTF and Mark VK5QN stepping in to give us a hand. Also on site was Mark VK5QI (Payload), Grant VK5GR (Balloon) and Will VK5AHV (Balloon). The team laid everything out and commenced assembling both the balloon train and the filling apparatus.

At the same time, Grant VK5GR started up his frist time chase vehicle and coaxed all of the linked software systems to life. Thanks to some loaned antennas from Matthew VK5ZM and LoRa receivers from Mark VK5QI, Grant was able to establish a full telemetry and tracking suite in just a matter of days to help assist with the chase.

Marcus filmed the proceedings too and you can see a short timelapse here of inflating the balloon.

Meanwhile, Mark VK5QN and Mark VK5QI (yes that did get confusing) assembled the balloon train. Mark VK5QN with his climbing and scouting background did a professional job of tying the balloon train together. You are most welcome to come again Mark!

Lift-Off

Finally the time came for liftoff. Mark VK5QI checked in with ATC Melbourne and we were given our clearance to fly. The team raised the balloon train and was thankful that we had almost zero ground winds. Mark did a final check that all the payloads were transmitting using a new handheld flight status monitor he had been working on and gave the the green light to commence countdown.

Grant VK5GR then released the balloon and we witnessed a near text book launch. As it climbed, the balloon hit it’s ascent target speed of 5m/s and everything looked good for a successful flight. The ground teams then scrambled to pack everything away and get rolling. It was going to be a long chase, with the landing zone predicted to be up in the north eastern Barossa Valley, and a detour around the River Murray required past Bow Hill and up to Blanchtown so that delays on the river car ferrys could be avoided.

Tracking Control

Meanwhile 58km to the north west, the ground tracking crew of Peter VK5KX and Darin VK5IX were awaiting signal aquisition as the balloon cleared the horizon. They had lots of signals to track this flight, including the 100 Baud RTTY, the LoRa Telecommand system and two Wenet Imaging payloads. Peter again setup his automated tracking antenna (seen on the previous week’s flight) and with Darins help was able to collect and upload to the internet the image signals from both payloads.

Peter took the following video of the Wenet systems in action

The Chase

Meanwhile, back in the two chase cars, Marcus VK5WTF, Mark VK5QI and Will VK5AHV headed out first and made the dash up to the valley.

Mark VK5QN and Grant VK5GR had a slightly slower start, as they had to first drop the gas trailer at a staging point in Younghusband before they too could join the chase.

Wenet Images

This was the first time the balloon and been flown this far NE of Adelaide so it was great to see some different angles of the state. The weather was nearly perfect as well with hardly a cloud in the sky. These photos were taken by the AREG Wenet payload with an outward facing camera.

This slideshow requires JavaScript.

One of the last photos actually captured a shot of Mark VK5QI’s chase car as the team was fortunate to be in visual range of the landing.

Grant’s team wasnt quite so lucky due to a software issue involving timezones and the prediction tools and he didnt make it to the landing zone until about 5 minutes after it landed.

Once the balloon landed, both teams met up with the local land owner before being given permission to drive in and pick up the payloads. We were very lucky that the balloon landed approximately 100m from the access track in an empty stubble field. Definitely one of the easier recoveries of recent times!

After we bid farewell to the land owner it was off back home – of course via another bakery (this time in the main street of Truro). Mark’s chase team had the luxury of being able to head straight back to Adelaide. Meanwhile Grant had to return to Younghusband to pick up the gas bottles and trailer. For the VK5GR team it was nearly a 600km 10.5hr round trip this time.

Flight Path & Statistics

Horus 47 flew an interesting course this time. This is a rather uncommon flight track for the AREG team.

The flight statistics are below

MetricResult
Flight Designation:Horus 47 - SHSSP18 #2
Launch Date:04/2/2018 23:59:04 UTC
Landing Date:04/2/2018 02:19:52 UTC
Flight Duration:2 Hours 30 Minutes
Launch Site:-34.878614 139.492314
Landing Site:-34.313174 139.107985
Distance Traveled:72.7 km
Maximum Altitude:32,507 m

Again many amateurs from across the state got involved in telemetry collection. We wish to thank everyone who took part as you all help make the chase and recovery more successful.

The following is the chart of who contributed to the telemetry gathering effort:

Thanks goes to the following who contributed: VK5QI, VK5KJP, VK5ST, VK5NEX, VK5EU, VK5APR, VK5KX, VK5GR, VK5FTAZ, VK5ZAI, VK5DJ, VK5FAAP, VK5ZEA, VK5ALX, VK5KIK

A few stations also contributed to receiving the Wenet digital imaging downlinks. These stations were:

SHSSP1 Payload

  • VK5APR: 145509 packets (35.52 MB)
  • VK5WTF: 91884 packets (22.43 MB)
  • VK5EU: 146129 packets (35.68 MB)
  • VK5DSP (UniSA Team): 133871 packets (32.68 MB)
  • VK5KX: 99419 packets (24.27 MB)

VK5ARG Payload

  • VK5QI: 198691 packets (48.51 MB)
  • VK5KX: 185197 packets (45.21 MB)

Conclusion

So that marks the end of the story for the Southern Hemisphere Space Studies balloon launch program for 2018. We hope everyone had a great time and again thank everyone who contributed or participated in making the flights possible!

73 till next time de VK5ARG

Acknowledgements: Thanks to VK5QI, VK5QN, VK5GR, VK5WTF, VK5KX, VK5IX, VK5AHV and SHSSP for all the material in this report.

Horus 46: International Space University – Jan 2018

Posted on by

The Amateur Radio Experimenters Group teamed up again this year with the International Space University’s Southern Hemisphere Space Studies Program to simulate a space mission using Helium fueled high altitude balloons.

The Southern Hemisphere Space Studies Program is an intensive, five week, live-in experience built around an international, intercultural, and interdisciplinary (3 “I”s) educational philosophy for which the International Space University (ISU) is renowned. The program provides a multidisciplinary understanding of the key activities and areas of knowledge required by today’s space professions, including:

• Space science and exploration
• Space applications and services
• Human spaceflight and life sciences
• Space systems engineering and technologies
• Space policy and economics
• Space business and project management and
• Space law and regulatory issues

The Balloon Mission – 2018

The original plan was to fly a multi-faceted ‘heavy’ mission that included downward as well as outward facing cameras, inertial measurement units reporting the camera orientation (so that the photos could be plotted and stitched together after the flight) and a spectrometer studying atmospheric gas makeup.

Unfortunately the weather was not cooperating, with flight paths landing in severe bush-fire rating zones within the Adelaide Hills, a risk the AREG team were not willing to take. So, at the 11th hour, the plan was re-cast to collect only outward images, without the flight termination devices on board, using disposable payloads. Thus, Horus 46 was born and flew on the 28th of January.

Predicted Flight track before launch

The Launch

 

(Video provided by Timothy Ryan @AstroTimOz)

The launch teams arrived at Serefino WInery at 8.00am and by 8:10am we had selected the launch and tracking sites. This year, due to the very calm ground winds we were able to lift off from the front lawns. The SHSSP students then helped with preparing the flight and filling the balloon. Grant VK5GR led the filling operations, aided by Josh VK5JO and WIll VK5AHV  while Mark VK5QI tended to the payloads, Peter VK5KX and Bill VK5DSP tended to the ground station receivers and Matt VK5ZM (club president) secured the balloon train and handled the publicity aspects of the event for AREG.

Telemetry and Images

Telemetry collection was vitally important for this flight as it represented about the only way that we were getting pictures back from the balloon. To this end, we again enlisted the help of Peter VK5KX and Bill VK5DSP who provided the primary image downlink stations for the day.

Mark VK5QI’s X-Quad antenna from Wimo generated a lot of interest as well as the tracking rig which now takes GPS data from the telemetry and computes the correct azimuth and elevation to aim the antenna at to receive the balloon. Lots of work went into that system by multiple club members so it was great to see it out in anger.

Back in Adelaide, Peter VK5APR and Graeme VK5EU also made major contributions. The Wenet telemetry scoreboard in the end was:

  • VK5KX: 275015 packets (67.14 MB)
  • VK5APR: 153431 packets (37.46 MB)
  • VK5DSP: 13682 packets (3.34 MB)
  • VK5EU: 89418 packets (21.83 MB)
  • VK5QI: 200777 packets (49.02 MB)

Tracking the RTTY payload required some finesse this time as it was an original Micronut complete with AFSK spacing and frequency drift issues of old. None the less multiple stations were able to contribute to the flight data collection.

What the Balloon Saw

The most spectacular aspect of any of these flights are the pictures collected from the high altitude cameras. These never get old and this flight did not disappoint.

This slideshow requires JavaScript.

(Slideshow from the flight)

The final flight track looked as follows

The flight stats are as follows:

MetricResult
Flight Designation:Horus 46 - SHSSP18 #1
Launch Date:27/1/2018 23:39:30 UTC
Landing Date:28/1/2018 01:58:43 UTC
Flight Duration:2 Hours 19 Minutes
Launch Site:-35.22103 138.55374
Landing Site:-35.38075 139.1722
Distance Traveled:58.8 km
Maximum Altitude:21,213 m

Attempted Recovery

As with all flights, there is a degree of uncertainty. So with Horus 46, while the expectation was that we wouldn’t be recovering this one, none the less an attempt was going to be made. Mark VK5QI set out with Will VK5AHV to track and attempt recovery anyway.

For a while it was looking positive, but alas this balloon “exceeded specifications” in a most annoying way. It flew higher than planned, in fact nearly 4km higher, which shifted the final landing zone well and truly into the waters of Lake Alexandrina.

Conclusion

A big thank you is again owed to everyone who contributed to the flight either through direct flight operations or through telemetry gathering. Stay tuned as we are still hoping to fly the main scientific payloads next weekend (weather permitting).

Horus 46 High Altitude Balloon Launch Sunday 27th

Posted on by

 The Amateur Radio Experimenters Group has been again asked to support the Southern Hemisphere Space Studies Program for the International Space University in 2018. Held in conjunction with the University of South Australia in Adelaide, this year AREG is launching one balloon for the group carrying a variety of sensors and cameras. The students this year are focusing on space navigation and will be attempting to take the GPS and 9DOF orientation sensor data from the payload to pinpoint where in space the photos were taken from, and then overlay them like a checkerboard over the ground.

The flight will lift off at 10:00am ACDT on the 28th of January from Serefino Winery east of McLaren Vale.

Tracking of the flight will be available on the HabHub Tracker, available at this link. (Note that other balloon launches will also be visible on this page, including the Bureau of Meteorology launches from Adelaide Airport).

Live Imagery from the launch will be available at this link: http://ssdv.habhub.org/VK5ARG

Payload Telemetry Details

UPDATE: Due to the weather, there is now only one camera payload (as well as the RTTY and tele-command systems) planned for this flight, with a much lower planned burst altitude (~17km instead of 30km). This is because of the flight path and recovery concerns in the face of Severe fire-ban and harsh weather forecasts.

  • Primary Telemetry:   434.650MHz +/- 5 KHz RTTY 100 baud 8N1
  • Imagery Payload:   441.2MHz FSK 115k2 baud Wenet

As always we can use the help with receive stations copying the telemetry and pushing this to the internet for us. If you have a Wenet capable ground station please concentrate on the 441.2MHz downlink to maximise the data we collect for the university.

The auto-configure feature within dl-fldigi will automatically configure these settings for you once you pick the correct flight (‘Horus / SHSSP 2018’). The UKHAS tracking guide provides the information you need to set up a RTTY receiver:  https://ukhas.org.uk/guides:tracking_guide

Note that the RTTY payload on this launch is one of our ‘vintage’ MicroNut payloads, and is expected to drift a few kHz during the flight. dl-fldigi will keep track of the signal if it’s within your receiver’s passband, but you may need to re-tune during the flight.

Information on setting up to receive the Wenet imaging payload is available here: https://github.com/projecthorus/wenet/wiki/Wenet-RX-Instructions-(Ubuntu-Debian)

Note that this is a few orders of magnitude more complicated than setting up for RTTY, and requires a machine running a recent version of Ubuntu, some Linux experience, and a RTLSDR+Preamp. You also need to be within 100-150km of the balloon to receive sufficient signal.

The Flight Path

This flight is not ideal as it is landing in the Adelaide Hills, an area that can make recovery difficult for multiple reasons. The planning group are watching this very closely.

A note on the Weather

With the weather in the high forties this coming weekend if the CFS issue a Severe or higher fire ban on Saturday at 4pm then the flight will be scaled back or cancelled. It is possible a light weight disposable flight may still run (without the expensive scientific payloads) so we will still be looking for tracking. It all depends on the flight path and the fire ban status issued by the CFS. A final call will be made Sunday morning and will be posted to the AREG Website before launch.

 

Next Meeting: Chasing DX (or how to work 3Y0Z)

Posted on by

Welcome to 2018!

The Amateur Radio Experimenters Group Monthly Meetings are starting up again with one of our Beginners Series  of talks, but this one will have a twist. We will be running it as a panel discussion with the topic “HF Operating Etiquette – How to Work 3Y0Z”, and wish to invite all of the active DX chasers and HF operators in the room to share their collective thoughts on what to do and what not to do when chasing HF DX in general.

The aim is to spread the collective knowledge about how to get through those piles for that special ATNO (All Time New One) like the Bouvet Island DXPedition (#2 on the most wanted list). Topics will be guided by moderators and will include HF operating etiquette, how to work HF split, how, when and where to call in a pileup, what to consider propagation wise and much more.

We will have a live scribe taking down all of the best ideas and will post them here after the meeting for future reference.

Where and when is the meeting?

Friday January 19th – 7.45pm (for an 8.00pm start)
Fulham Community Centre, Phelps Court, Fulham.

Visitors are most welcome to come and participate in the evening. We hope to see you there!

[wpgmza id=”5″]